Problems with extrusion of PP beams – Help needed
- This topic has 16 replies, 7 voices, and was last updated 2 years ago by .
Hello PP community,
I am trying to extrude plastic beams for construction, in Maputo, Mozambique. Particularly, I am interested in developing a solution for roof structures, as plastic would have certain advantages compared to conventional solutions, e.g. not rotting or getting eaten by insects. I have setup a small workshop with a shredder and an extruder and we have run some tests but are facing some problems.
We are seeking to produce beams like in this video: https://www.youtube.com/watch?v=zNGuuSKE1pY
However, we haven’t been able to produce beams longer than 1,5-2 meters. The machine lacks capacity to fill up the mold before the plastic cools down and solidifies. Sometimes it clogs the mold and we have to make new molds.
Do you have any suggestions to how we can produce 3 meter beams, using our small scale machine? Or would i simply have to buy a machine with larger capacity?
Thank you in advance, Johan
we are trying to produce beams for construction of simple roof structures.
WOW Johan! You are actually doing quite well with the beams you are creating with this machine! Again if you search the forums for NiTi wire to heat the tube you should be able to produce longer beams.
Keep in mind that a larger machine just means a new set of problems and challenges! More than likely more electrical requirements, more space and more costly failures.
Also grinding the plastic smaller will help the melting.
Your specifications do not necessarily tell the whole story…
“2,2 Kw motor, single phase and around 1400 rpm. we are using a compression screw.” We also need to know the gear ratio of the gearbox, voltage of the motor, length of the working area of the barrel and screw, diameter of the screw and barrel, what does your connection from the motor to extruder screw look like in pictures, materials used (PP or HDPE or mixture), square size of the beams (25mm x 25mm)?
Are you grinding scrap at the same time as extruding plastic? Just do one at a time to get maximum power.
I hope this helps and look forward to your response.
but i essentially have to acquire a machine with greater capacity in order to extrude beams at greater length?
thanks for the feedback.
it is a 2,2 Kw motor, single phase and around 1400 rpm. we are using a compression screw.
You need to heat the beam molds or you will never get there even with a compression screw. That is quite a long length for the pp Extruder. It is possible it will not produce enough pressure to fill that length with such a small Extruder. Best of luck!
Do you use the compression screw (as in the video) or the wood drill?
Which kind of motor do you use (power, rpm) ?
awesome work! but dont throw away molds! if there is plastic stuck in them, find a way to heat them up and get the plastic out that way.
greetings from peter /The Netherlands
@jmot So i think your “brittleness” might be better described as the plastic not melting together very well in a cold mold. (ie cold steel tube) I would refer to this topic for more information.
Screw speed related to the gearbox ration will be important to outputting as much material as fast as possible. Again that information should be located on the metal data plates affixed to the motor and gearbox. I would just post a pic of the dataplate for all to see.
@jmot, yeah, I just wanted to point this out also for other readers. I see very often projects being kinda stuck at the ‘make it work’ stage and so hardly make it to the next level, ‘make it good’ and then ‘make it fast’. Crucial details of successful projects are quite rare. I am happy to hear about the rods now, well done 🙂
i don’t think brittleness is the issue – i think it is lack of pressure in the mold and speed/capacity of the machine are the main problems.
regarding safety. we joined the plastic beams with the wall with steel rods cast into the wall with concrete. should be safe.
If you are using plastics that have been recovered from sitting outside in the environment, then PP degrades very quickly in UV sunlight. (In as little as 6 days.) That would explain the brittleness of the PP.
HDPE has much better natural resistance to UV Sunlight.
thank you for the positive feedback.
regarding the length – we haven’t been able to produce beams longer than two meters, so the prototype showed above is quite small. around 1,5m, i believe. it is a toilet. regardless, the beams are probably not strong enough to cover larger spans by themselves. however, we are trying to solve this by triangulating the structure and join several beams. i will upload images, once we are further in the process.
Great work, as a back-up if the long extrusion proves difficult, Maybe try some heat welded lap joints to create a longer beam. I would probably include a bolt just for extra security.
i’m not aware of all the detailed specs of the motor. i will look into that and send more photos later.
we are not shredding and extruding at the same time.
we have used pp and hdpe – we haven’t tried mixing different plastics yet. we had better results using hdpe. we were able to extrude longer beams using hdpe and pp breaks more easily.
You must be logged in to reply to this topic.