We've just launched our map. Add yourself by clicking here!


[USA]Company Making Shredder parts updated Oct2019

Andre A. dreek00

[USA]Company Making Shredder parts updated Oct2019

18/01/2017 at 05:43

Hello guys!

The company that is working with me to get the shredder parts is called “BBC Steel” and they are located in Oregon.

New Prices as of Oct 2019: ( so far the lowest in USA)
– 1 set $425.00
– 2-5 sets 300.00ea
– 6-10 sets $285.00set
– Shafts are still currently at $38.00 but could raise.
– Bearings $17.50ea.
****Shipping is not included – You will have to pay for shipping****

Important: This modifications were necessary for most accessible parts also to keep the prices low.

Blades were modified to fit the 1″ shaft (this set will fit perfect if you buy their shaft and bearings)

Shaft is 1″ with ends machined to 3/4
Bearings are 3/4

Website: http://www.bbcsteel.com
Contact for BBC Steel: Randy [email protected]

You can email Randy Including your name and state you would like to order the shredder parts, keep in mind the prices may be going up due to the material going up in price. BBCSTEEL is one of the few companies that is wiling to work at small scale (one set at the time) Not all companies are willing to work this way since we can’t order in bulk (100s at the time)

Again, We can not afford to lose this company so email with discretion and be polite, this would be ideal for people who require receipts and invoices (If for business, School districts, Non Profit)

Any question don’t hesitate to message me.

I invite everyone to join “Precious Plastic USA” group on Facebook

***If you have a better option of better deal please let us know as we always look for better ways to bring cheaper and more accessible options for the community****

133 replies
7 subscribers
6 saved
sort on most likes
22/01/2017 at 19:33

Just for clarification. This is for a complete plastic shredder unit, minus motor, for $1,050 for one, or $850 per unit in groups of ten? And an additional $150-200 for shipping and handling?

23/01/2017 at 14:55

@benismobile Hi, that is correct. Chris from upstate New York @chriskudla found a company with even lower prices, this is break down:

1 set- $650
2 sets- $550 each
10 sets- $375 each

plus shipping

I still have to confirm with Chris on sizes. Also, I am in for the group buy and I am willing to make this happen I just have to coordinate with Chris.

24/01/2017 at 18:22

Ok, that definitely looks better than the previous quotes folks were sharing. I’d like to get two units. So, how do we make this thing happen on our ends? Does @chriskudla send us a note with an email address or something?

24/01/2017 at 23:21

Here in Oregon, I got the parts for my shredder laser cut in Stainless Steel for $317. It would have been cheaper if I had bought 5 sets. The guy quoted me for 1 set and 5 sets. If I had ordered 5 sets at time, it would have been about $193 per set.

Attached is the orignal quote. They guy did it in kind of a confusing way, so I parsed the info into spreadsheet, which you can check out here.

Also included a pic of the working shredder! If this is the best price folks have found, I’d be happy to coordinate a group buy.

25/01/2017 at 21:30

@samsmith Wow!Yes please Im glad you came across this post! thank you!

Yes email me to [email protected] to coordinate

I will post the update now!

25/01/2017 at 21:51

@xxxolivierxxx any idea why I cant update my topic anymore? only have the reply button 🙁

Can you please Ping this post? We would appreciated so much!

Thank you Guys !

25/01/2017 at 23:11

should be fixed now @dreek00

26/01/2017 at 01:49

@davehakkens Thank you Sir!

(Sam) and I will be coordinating the “Group Buy” once I get the formal quote I will post it and take it from there. So, please all interested people comment if you are interested in the group buy and this way we can help lots of fellas in getting their shredder parts. Thank you Guys!

Can you help us spread the word?

guys comment if interested










26/01/2017 at 02:54

I’m in Seattle and I was quoted about 3 times what @SamSmith paid. I would love to get in on a group buy!

26/01/2017 at 04:34

I’m definitely interested in the group buy, specifically to get two (2) units for myself.

I’m not on social media these days, so I wouldn’t be in any positon to touch base with other makers outside of email, but here are the urls to a few NYC area maker labs to gauge if they’d be interested.


And of course, you’ve got the iMakr Store in lower Manhattan you could reach out too, imakr.us. They sell 3d printers, but I imagine their people might be curious about this.

I’d spread word myself, but I wouldn’t know how to introduce myself out of the blue to anyone interested.

26/01/2017 at 17:05

@benismobile @bgrocks thank you for supporting this group buy I will let everybody know once everything is set up please drop your emails here

Sam check your email

26/01/2017 at 21:22

@dreek00 Email sent to [email protected].

26/01/2017 at 21:24

Are these quotes for using metric steel or did someone convert to Standard ? thanks, Lee

26/01/2017 at 21:45

@leebarnard I will have to confirm that with @samsmith im pretty sure is metric but is if not, Sam assembled the Shredder so in the case of the parts are in Standard it will work and fit properly

26/01/2017 at 23:11

Yeah the version I built was metric, with the 27mm spindle. If I had read the forums first I would have just converted it. Instead I ended up ordering a 27mm hex spindle from McMaster Carr for way too much money. I also found that the bolt holes to keep the fixed teeth together were slightly bigger than the bolts I was using, causing the teeth to wiggle a bit. Not sure if the standard version accounts for that.

Anyway, if I were to do a new run, I would get the Standard version done, not metric. I’ll send Randy the quote request today.

27/01/2017 at 16:56

@samsmith Thank you Sam, please email me the information once you have it Thank you!

27/01/2017 at 18:00

Hi, I am extremely interested to get in on the group buy for the shredder parts. I’m looking to start recycling plastic in Lexington, Kentucky. My email is [email protected] – Thanks!

27/01/2017 at 18:29

@willhanrahan Thank you! I will keep you updated (email sent)

30/01/2017 at 02:59

I am interested in getting at 1 at $200, or possibly 2 sets, depending on how much cheaper it gets.

30/01/2017 at 06:12

I may be interested in a set of shredder part. I know someone who gets a lot of gears waterjet cut. If someone can send me a link to a standard set of files I can ask him about getting a quote. I live in Michigan.

George A.

31/01/2017 at 07:57

@SamSmith @AndreApercana This sounds really, great. Can I get in on this? I live in Macon GA.

31/01/2017 at 08:00

Sorry for mispelling. Just sent email to [email protected] @AndreAparcana

31/01/2017 at 08:03

What I would like to do is use the shredder to make pressed boards for bat houses. I want to go down to my farmer’s market and collect recycled materials from interested folks, shred their plastic, wash, press, bathouse! Will have to play with construction and colors to get thermal properties right.

31/01/2017 at 08:10

don’t mean to blow this thread up, I’ve sent an email already, I just don’t want to fall through the cracks so let me post my email here, its [email protected] . I gotta say I’m more than a little stoked heheh. ok thanks folks.

31/01/2017 at 18:27

@jdhe @albercook @lesir Hello guys! We are still waiting on @samsmith for the formal quote and we will take it from there. I will reply to emails now.



01/02/2017 at 03:20

Hello Guys! Sam @samsmith got me the update on the group buy. Unfortunately the company under quoted Sam for the shredder parts.

New prices are
1-4 sets $400.00 per set,
5-9 sets $375.00 per set,
 10-20 set $345.00 per set.

01/02/2017 at 08:24

Where might I find shredder plans for standard thicknesses? Has anyone cut a set using these plans? Will get some prices in Florida. MLB

02/02/2017 at 00:47

And those are the lowest solid quotes we’ve got so far?

02/02/2017 at 01:22


I would like to be a part of this group buy. I am 100% committed to getting these machines built for myself! Please feel free to e-mail me concerning all updates pertaining to this purchase at [email protected].

02/02/2017 at 03:18

OK, so I may have access to a CNC plasma cutter. I think there would be a lot more work needed to clean up the parts than water jet and even more than laser cut. I don’t know what the Kerf will be. Has anyone gotten a quote on just the steel?

I would want a set of drawings that have been converted from metric to standard. I saw mention of someone having done that on this forum but with the search function not working it is hard to find things.


Viewing 30 replies - 1 through 30 (of 133 total)

You must be logged in to reply to this topic.

Support our projects on Patreon so we can keep developing 💪