Forum Replies Created

Viewing 30 replies - 1 through 30 (of 31 total)
sort on most likes
helper
14/03/2020 at 17:54
0

Yes, you just need a way to move air. It can be accomplished in many ways, for the requirements, skills, and funds.   It can be air to move up. or use water to bring down. You have the idea. Now build a model and then test it out 🙂

helper
14/03/2020 at 17:30
1

Well, you have the mind on an engineer it seems 😉  This is the best system set up for Kinetic Energy Generation. 30′ tank, pipe, tube, etc. you have a conveyor system inside of the tank. On the conveyor, there are airbags, that are open in the bottom to all Gas to enter from the of water at the bottom of the tank.
This Gas is H and O2, as with Boyle’s law gas pressure and volume. The gas will rise and double in volume. This will raise the airbags on the conveyor, thus pulling the system up. On top of the tank is a Generator that will convert the lift energy to rotational Energy to turn the Generator

Yet the Gas that was created and use to lift the conveyor system, will now be dump/released and can be collected and burned in a Gas Turbine to generate energy.

The system can be started with an air compressor. Air will lift, turn the top generator, Electrical power can they be feed to the electrolysis system to continue making the Lifting gases.

Then the gases can be burned to create additions power.

Actually a small wind turbine on top of the tank can replace the Air compressor. The gases generated will be plenty. If or when this system is used on offshore wind turbine structures the Gases can be stored underwater in Flesbags attached to the seafloor. It a way to store energy form Wind 😉

So now you have a power generation system that can provide 2-4 ways to create energy. It all pretty simple. Yet maybe too simple, this is why, it’s not on every home. Gov will have no Income from the People using Power 😉

In time maybe I will build a unit for proving the method. Or you can 😉
Cheers
Craig

helper
14/03/2020 at 15:34
2

Look like you have a Kinetic energy system that uses buoyancy to push water around. Not new https://www.youtube.com/results?search_query = Kentic + power Many system designs out now. Yet can be improved on.with a Trompe design https://www.motherearthnews.com/renewable-energy/hydro-power-zmaz77jazbon

helper
12/03/2020 at 14:34
2

Hi Ryoma, Your English is good J I’m not an expert as such. Just a person that is passionate about this. Been studying it for 4-5 years now and see GREAT things in this new Industry. Yes we can build Graphene supercapacitors for storing power from Solar or any power generation source. Even get power from the main grid to power up the batteries and run your home, office of the battery bank. Thus saving greatly power usage from the main grid.

We need to get off burning things for our power requirements. Yet there are some things like methane from Bio gas is ok, to a degree, yet should be limited.  If you like to learn more about Graphene, follow Dr. Robert Murray Smith https://www.youtube.com/channel/UC4AkVj-qnJxNtKuz3rkq16A

helper
12/03/2020 at 13:45
1

Yes, I do know about heating films. They are great and need more of them for in-floor heating foe sure. You may want to do more research, about Heat transfer within a room via Convection https://www.simply.science/images/content/physics/thermal_physics/heat_transfer/Concept_map/Convection.html From my research, one sheet of 4’x9′ drywall will heat a 20’x30’x9′ room and uses less power than 0.8kw.
Yes, I’m doing testing. You did not see this in the videos I posted above?

helper
11/03/2020 at 23:35
1

Hi  16pxdesign thanks for your message. I was waiting to get the final design from timdetlor yet nothing for a while now?? I have been working with the Graphene and creating a heat wall with Graphene Paint.

I could draft up the simple drawing, yet wanted to get others that have passion for doing such. It’s such a simple drawing I figured I have it in 1-2 days. Then move forward to get a mould created and then we could be making Batteries.

Yet as you see we are still looking to get others looking, sharing and working on this.

Some vids on the Heat Paint.
https://www.facebook.com/craigglewis1/videos/3133532246678517/
https://www.facebook.com/craigglewis1/videos/3133591600005915/
Making Graphene

And more on my Youtube
https://www.youtube.com/user/craigglewis/

helper
11/02/2020 at 20:32
2

Hello All, Just seeing if there is someone that wants to continue this project. Still looking to get design and then a mould, create and them get manufactured.  It’s a great project if you are looking to build batteries for off-grid. We had a good start, yet been stopped for a few weeks now.

Cheers,
Craig

PS I have order supplies to make batteries and to make Heating walls 🙂

helper
31/01/2020 at 17:20
3

It looks to be a simple system. Yet Buring fuel to make fuel to burn, is not helping to keep the CO2 down. it is a solution, yet maybe not burn and create other products 🙂

helper
28/01/2020 at 02:18
1

There are no terminals as such. It depends on the uses and configuration. The Sidewalls 9Graphfoil become the terminals. Yet we will have to run two wires to connect to equipment.

I have not created this type of battery before. I need to create the parts first. So I figure that I start with creating the Battery frame. Then I can order the materials to build the batteries.

I will make videos and post the Build 🙂
Craig

helper
27/01/2020 at 08:19
1

Hi Tim,

Not critical 1mm best No.
Less chipping and ease of release from the mould.

The HPDE component is the Frame of the Battery.
Several layers of Graphfoil and Carbon Black sheets, are heat sealed to form the Sidewall.
The hole is the fill hole for  Zinc Bromide.
The hole gets sealed and then changed the battery.

Build many, create battery banks and be off-grid. Or for Emergency Power

Cheers, Craig

PS next Moulds, EV scooter/car Full 1 piece Frame, with GHDPE and Drive Wheel Hubs.

helper
26/01/2020 at 21:19
1

Tim, we just need the 1MM Rad on the outside Corners and to looks like all we need for the design.

Great job, TY 🙂

I’m thinking that we can mould into individual uint,  or several.

Yet maybe able to press in a continue tube and cut to 1cm Wide??

Cheers,
Craig

helper
26/01/2020 at 18:50
0

@nicam Join us and we can share “POWER we ALL Need and Can HAVE It!!”  https://davehakkens.nl/community/forums/topic/power-we-all-need-and-can-have-it

Cheers,
Craig

helper
26/01/2020 at 18:42
1

Hi Tim, Great to get this from you. TY

1. There is no bottom, Just sides walls frames (HDPE sheets will form the top/bottom walls)
2. Corners will have a Rad. 1mm? or cutting tool dia.
3. I forgot to mention the Liquid fill hole. On 1 side of the 8cm sides, need a 2mm hole in the center or 4CM from the edge.

The Drawing can show the hole. Yet when making the mould, maybe easier to drill the hole out as to creating a Mould??

Thanks and looking forward to building 🙂
This could also be printed with  3D printer HDPE Filament.

Cheers,
Craig 🙂

helper
26/01/2020 at 01:24
0

What plan, or vision do you have?

helper
25/01/2020 at 19:17
1

Yes that is Correct Zinc Bromide Batteries. I have a way to create on a small scale and once we get set up, can mass produce, and open it up for others to Create 🙂

https://scholar.google.com/scholar?hl=en&as_sdt=0%2C5&q=zinc+bromide+batteries+&btnG=

helper
25/01/2020 at 02:07
2

Hi Tim 🙂

Thanks for this.

The Battery is getting 1.85V 3A with 10K cycles at this time. Yet we are looking to get more with bigger batteries in the future. We want to create a battery for Charging cell phones first.

Cheers,
Craig

helper
24/01/2020 at 22:03
3

Hello Canada,
Craig from NL, and we are digging out from the Super Winter Storm and 80cm of snow. It’s Canada A 😉

I have lived across Canada, NL, NS, NB, ON, QC, AB, BC, and travelled through the rest. We have a Great Country, yet we have a lot to do to make it the Best.

Each of us is doing a small part to make it the BEST!!

I’m interested and looking into setting a PP in NL. There are a few on the Map.

If you have not, done. Look to see if you have funding available to you, for Creating yours. In NL we have http://mmsb.nl.ca/funding-programs/  I’m hoping to get a $15K Grant to start.

Yet at this time I’m looking to create Batteries so that we can become more sustainable.

I need to get an HDPE Case designed, Moulds built, and Manufacturing components

https://davehakkens.nl/community/forums/topic/power-we-all-need-and-can-have-it/

If you have the skills to Create the Design, Make moulds, manufacture.
Then let’s do this.

Cheers,
Craig

In reply to: Shredder motor

In reply to: Shredder motor

helper
28/12/2019 at 20:16
1

For the small amount that the Shredder can spread at one time. I feel that the motors are overrated. Liking the idea of the mobile unit, has anyone tried a 12vDC high torque, low-speed motor?  like these shorturl.at/fDUV4

Much Cheaper and lighter 🙂

I have been looking at the idea of making the Shredder with Plastic,
components.

Thoughts
Cheers,
Craig

In reply to: Let's win together!

helper
28/12/2019 at 18:23
2

Great Idea and resources for getting funds, Dave 🙂

Are you able to list the awards that you have received to date?

Be great to know the success you are having.

This one may be of interest, yet only 18 days to submit.
https://www.startup-energy-transition.com/ 

Cheers,
Craig 🙂

helper
27/12/2019 at 01:56
0

First, you mine the Graphite. Crush to different mesh size, depending on the Flakes needed for the market. To make Graphene there are several different processes. In the past, mass production was the problem. That is now solved and mass production of graphene is possible. This will open the markets to Graphene now. You can buy here for testing. https://workingink.co.uk/   What Robert to see what we can now do with Graphene 🙂 LOTS :)) https://www.youtube.com/channel/UC4AkVj-qnJxNtKuz3rkq16A

I will have to order more paint to work with.

Cheers,
Craig

helper
27/12/2019 at 00:06
3

Any pics, videos, to share.

Great work and keeping Precious Plastic alive 🙂

In reply to: mold quick release

helper
23/12/2019 at 23:27
1

Getting a few buckets for testing 🙂

Attachments:
helper
23/12/2019 at 23:12
1

Was this problem resolved?

helper
23/12/2019 at 20:56
0

Seasteading is a Great idea. https://www.seasteading.org/

Yet I would look to getting into International waters to have or create True Freedom and become the Plastic Nation.  Floating islands can be made with GHDPE Composit Structure and Graphaircrete for the Floating Modular Block

helper
23/12/2019 at 20:48
0

Is this the Video?

From packing peanuts to disposable coffee cups, each year the US alone produces some two billion pounds of Styrofoam — none of which can be recycled. Frustrated by this waste of resources and landfill space, Ashton Cofer and his science fair teammates developed a heating treatment to break down used Styrofoam into something useful. Learn more about their original design.
https://www.ted.com/talks/ashton_cofer_a_plan_to_recycle_the_unrecyclable

helper
23/12/2019 at 20:29
0

Yes it would be great to get the stats and see what the best ratios are for making pavement blocks

Cheers,
Craig

helper
23/12/2019 at 20:25
0

Not sure if dog owners would like their dogs to be chewing on plastic. Yet there seems to be a lot of toys made for dogs, out of plastic.

Thy Graphite/Graphene.

helper
19/12/2019 at 00:19
2

My email [email protected]

Thanks for your comments and interest.

Cheers,
Craig

Viewing 30 replies - 1 through 30 (of 31 total)