Forum Replies Created

Viewing 12 replies - 1 through 12 (of 12 total)
sort on most likes

In reply to: Sheet Press Mould Oven

helper
03/07/2019 at 14:53
2

The link in the post above yours contains the most recent model, this is not likley to change before October

In reply to: Sheet Press Mould Oven

helper
29/06/2019 at 01:43
3

The model of the oven is almost complete, just missing the electronics. The files can be downloaded here if anyone would like to give some feedback (SW2018 and STEP format)

https://drive.google.com/drive/folders/1wu9SgA0YuSP9UXOoQn6icHOrc7_71dSz?usp=sharing

In reply to: Sheet Press Mould Oven

helper
21/06/2019 at 00:24
2

Test of sheet press oven door prototype V4.2.1

A little heavy but the mechanism is smooth and it closes almost perpendicular to the oven opening which allows for a snug tolerance between the inner and outer parts of insulation. We have decided to add a second layer of L extrusions to the inside of the door to protect the insulation and also considering chaning the 40×40 Ls to 20×20 to reduce weight. In This video the door sits slightly open at the top, this is because the insulation on the door (deigned to fit V4.2) is pressing against the insulation inside the oven (V4.1). If this continues to happen in the next version the 80mm horizontal tabs can be extend t o120mm so the door sits further back past the center of gravity.

Attachments:

In reply to: Sheet Press Mould Oven

helper
03/06/2019 at 15:36
2

So after one week of testing the three scenarios we have made the follow observations.

The Mineral Wool insulates much better than the AAC, the external temperature of the box is actually more susceptible to the outside temperature, it dropped towards the end of the day as the sunlight dropped.

When heating the same volume of space the Mineral Wool used 0.7kwh to maintain a temp of 220’C whilst the AAC used 2.6kwh. Making the Mineral Wool more than 300% more energy efficient than the AAC.

Two layers of Mineral Wool accumulating to 140mm and one layer of AAC  measuring 80mm in thickness were used to insulated identical volumes of space. The decision to use a thicker wall of Mineral Wool was made due to its lower cost, meaning the real world situation is more likely to be the same. It is also easier to overlap the two layers to prevent thermal bridges between the inside and the outside of the oven.

Although the Mineral Wool is better at insulting and has lower cost it is also weaker than the AAC it requires some additional infrastructure to secure it in place and protect it from damage. We tested two scenarios: 1.) A closed steel box and 2.) A skeletal frame with a steel plate in the bottom to protect from dripping. Both scenarios performed almost identically in terms of power consumption, insinuation and retention of heat.

This leaves us and future builders of the oven a pragmatic decision to make. The steel sheet appears more friendly and similar to a finished commercial product which we are used to seeing. It also offers more physical protection. The down side is that it adds a significant amount to the cost (750-1750) euro dependent on your location and increases the duration and complexity of the build.

Attachments:

In reply to: Sheet Press Mould Oven

helper
27/05/2019 at 13:40
3

This week we are testing Insulation types!

We are going to start with two insulation materials, AAC and Mineral Wool.

We have built two boxes with the same size internal chamber and a portable electronics rig with a single heating element attached to a PID.

The AAC is  secured from the outside walls and left exposed on the inside of the oven, this is the approach we used for V1 of the full size oven.

The mineral wool has an internal steel box to protect the insulation. I also plan to test an internal frame, instead of internal box depending on if the first results seem promising.

My first observations from building the two boxes is working with the Mineral Wool is a lot faster, cleaner process and weights a lot less than the AAC due to its ease of cutting and weight.

It is also cheaper so a thicker wall can be added and still at less expense than the AAC.

The results from the tests we will be running can be seen here.

We will be simulating a full working day for the mould oven (8 Hours).

We will be collecting data about the following parameters:

-External Surface Temp (Over Time, Regular Intervals)
-Internal Surface Temp (Over Time, Regular Intervals)
-Time to reach 220 (PID)
-Temp drop after open for 2 mins (PID)
-Time to return to 220 after open for 2 mins
-Power Consumption after 8 hours (KWH)
-Cool Time Back to 30 C

Attachments:

In reply to: Sheet Press Mould Oven

helper
17/05/2019 at 19:58
3

We made a prototype of the proposed door mechanism for version V4.2. of the oven.

Feedback would be appreciated!

In reply to: Sheet Press Mould Oven

helper
17/05/2019 at 16:50
0

Thankyou for the input 🙂

In reply to: Sheet Press Mould Oven

helper
13/05/2019 at 19:34
0

Hey Community,

We are prototyping v2 of the oven which will be part of the sheet pressing system.

Does anybody have an information about insulation types that they would be able to share? We have complied a list of types available in the Netherlands but it would be great if we could know what is available in more remote parts of the world, what you guys have learned from working with these, and if you have any sugestions of alternatives?

AAC

Calcium

SilicateIsofour Plates

Phar gas Plates

Vermiculite

Ceramic Brick

Ceramic Felt

Many thanks!

helper
02/05/2019 at 19:31
3

Hey everyone! Six months in and we have our first working prototype of the sheet pressing system up and running! Below is a presentation which highlights the journey so far and a video of the process so you guys can give us some feedback!

Attachments:

In reply to: Sheet Press Mould Oven

helper
09/02/2019 at 20:59
0

Hi Richie, the project is coming along nicely, it is in early days but will be finished by October. We will open source it so you can replicate it 🙂

In reply to: Sheet Press Mould Oven

helper
04/02/2019 at 13:38
0

I have an open question for the community.

Our first design uses ceramic insinuation bricks to contain the heat. We would like to find out more about the availability of ceramic insulation bricks. Could anybody provide some information about the availability of them in low resource areas.

Example
https://www.ebay.com/bhp/insulating-fire-brick

If people have any alternative suggestions to the ceramic bricks that would also be greatly appreciated!

In reply to: Sheet Press Mould Oven

helper
04/02/2019 at 13:32
4

We have developed a 3D model of the first prototype oven. I have attached a picture with a presentation detailing the construction process and some of the areas we still need to research.

Attachments:
Viewing 12 replies - 1 through 12 (of 12 total)